View source for Spin-Y (V2) manual

This is the manual for Spin-Y2（V2）, V1 is here: [[Spin-Y manual V1]]
----Spin-Y is a throttle for VESC and common e-scooter/bike.

Buy link: https://spintend.com/products/two-way-throttle-spiny-for-diy-escooter-diy-ebike
==Feature==
*Maximum Hand grip, specially at full throttle.
*Bidirectional operation (forward accelerate, backward e-braking) .
*Remapped 0-3.3v signal, extend the hall range to get more interference immunity, and safe for VESC and similar controllers compared to common 5V throttles.
*5v signal out put for All standard controllers like Minimotors/ Dualtron/ zero/ Vsett and others.
*Variable e-brake up on reverse scroll.
*Standard controllers use it mid to max as throttle only, can block with screw backward rotation! Reverse scroll can be blocked by replacing one screw for a longer version (included), if user on standard controller doesn’t want it to scroll backward (one way operation)
*Button at the back can be used for external function (dedicated signal wire) .
'''Note: The rear button is now bound to cruise function of Spin-Y itself, don't connect the 'rear button' wire to any external device.'''

==Specification==
{| class="wikitable"
|+Electronic Specification
|Working voltage
|3.3-5V
|-
|Out put resistance of VESC/normal throttle, variable brake
|330 ohm
|-
|ON resistance of Rear button and E-brake
|22 ohm
|-
|Off load current, 5V supply, no driving out
|Less than 50 mA
|-
|Normal throttle and variable brake output range
|0--4.2V, adjustable
|-
|Variable brake output range
|0.7--4.2V
|-
|VESC throttle out put range
|0--3.3V, bidirectional, 1.65V at center position
|-
|Two head buttons
|12V, 2A
|}All the values are approximate value, at 5V supply, unless otherwise specified.
{| class="wikitable"
|+The color of wires
!Color
!Function
!Explaination
|-
|Black
| - GND
|Negative power supply, and low side of rear button and E-brake switch
|-
|Red
| + 3.3/5V
|Positive power supply, can accept 3.3-5V, recommend 5V
|-
|White
|VESC Throttle
|VESC ADC1, centered  (bidirectional)
|-
|Green
|Normal Throttle
|One way signal for normal controller(ESC), NOT for VESC
|-
|Yellow
|E-Brake ON/OFF
|ON/OFF to GND for  ESC brake
|-
|Blue
|E-Brake variable
|Variable brake for ESC that support it, like some ninebot, xiaomi, Sabvoton, Kelly and other
|-
|Orange
|Rear button
|'''Deprecated, because the rear button is now bound to the internal cruise function.''' 
|}
==Calibration==
We can do three calibrations to make Spin-Y working more perfectly: wheel travel calibration, start point adjust for normal throttle, and end point adjust for normal throttle.

Spin-Y has three LEDs, under the wheel, to indicate the calibration state: green, yellow, red.  For easy to observe the LED state, do calibration at a darker place will helps.

By hold the rear button when power on the Spin-y more than 3 seconds, Spin-Y will enter the calibration mode.
===Wheel travel calibration===
Spin-Y can be more accurate after calibrate the wheel travel. Both the One way or two way mode are benefited.
#Hold the rear button during power on for more than 3 seconds, till the yellow LED start blinking, then release rear button.
#When yellow LED blinking, scroll the wheel to min and max for several times, then release the wheel.
#Quit, hold the rear button more than 3 seconds again, till the yellow LED stop blinking, and the green LED on.
#Check if the function is normal, if not, go to step 1 and try again.
===Start point adjust for normal throttle===
Start point is for normal ESC, usually they have start voltage at 0.7V and end voltage 4.2V.

You can observe the ESC and motor to find the right start point.
#Hold the rear button during power on for more than 6 seconds, after the yellow LED blinking, the green LED will start blinking, then release the button.
#Push forward (accelerate) the wheel to rise the start point voltage, Pull backward (brake) the wheel to lower it, 0.025V a step. Watching the ESC, when the ESC starts to spin the motor, pull back the wheel 2-5 steps to lower the start point voltage to get a idle voltage.
#Quit, hold the rear button more than 3 seconds again, till the green LED turn to solid on.
#Check if the start point is meet your requirement, if not, go to step 1 and try again.
===End point adjust for normal throttle===
End point is for normal ESC, the ESC's acceptation of the end voltage is varying, adjusting the end point can match their requirements.

You can use a multimeter to measure the voltage of the wire (green) to get an accurate end point voltage, or watching the ESC and motor to make the decision.
#Hold the rear button during power on for more than 9 seconds, after the yellow LED blinking, green LED blinking,  the red LED will start blinking, then release the button.
#Push forward (accelerate) the wheel to rise the end point voltage, Pull backward (brake) the wheel to lower it, 0.025V a step. Watching the ESC, when the ESC accelerating the motor no more, or the Spin-Y's throttle voltage meets your ESC's requirement.
#Quit, hold the rear button more than 3 seconds again, till the green LED turn to solid on.
#Check if the start point is meet your requirement, if not, go to step 1 and try again.
'''Warning “End point Configuration” process will start your motors spinning, have your scooter on a riser (wheels in the air).'''

==The E-brake and the variable brake==
When pull backward the wheel, the E-brake and variable brake wire will output a voltage, they can be used to control the controller's regenerative braking.

The difference of two brake signal is:

E-brake is a ON/OFF signal, when pull back, the E-brake wire connected to GND, when wheel at center of push forward, E-break wire off to GND.

Variable brake is a proportional (analog ) signal  follows the wheel's backward travel, when wheel at center of push forward, the variable brake wire outputs 0V, when pull back, outputs a 0-4.2V voltage as well as the angle of the wheel being pulled.
==The VESC throttle and normal throttle==
The VESC throttle is in 3.3V range, pull backward is 0V, push forward is 3.3V, the center is 1.65V.

The default normal throttle's range:

Backward to center----0V.

Center to forward----0-4.2V.

'''Reminds：If you're using our [https://spintend.com/collections/diy-electric-scooter-parts/products/ewheel-adc-adapter-v2-for-diy-ebike-escooter Ewheel ADC adapter] to wire with the SPIN-Y throttle, should NOT use VESC throttle cable, and need to use Normal Throttle cable'''
==Connect to Adapter V2==
Our Adapter V2 is designed for 5V hall system, has built in 5V-3.3V voltage translator, so recommend to set Adapter throttle supply to "5V“.  The rear button can be used as cruise control, and recommend to set VESC ADC control mode to "Current No Reverse Brake ADC2" to use cruise feature.

Make connection as below:
{| class="wikitable"
|+The connection for the Spin-Y to Adapter V2
!Color
!Spin-Y wire
!Adapter V2
|-
|Black
|GND
|GND
|-
|Red
| +3.3V/5V
|5V
|-
|Green
|Normal Throttle
|THR
|-
|Blue
|E-Brake variable
|ABRK
|-
|Orange
|Rear Button
|Cruise (the none-GND pad)
|}
==FAQ==
===How does on/off brake and external cruise button function work?===
When the rear button is pressed, it's wire(orange) will connect to the GND, there is a 22 ohm resistor serial in the circuit, to prevent short.  When button released, the connection to the GND will be open.

When the pull the wheel backward (to right), it's wire(yellow) will connect to the GND, there is a 22 ohm resistor serial in the circuit, to prevent short.  When wheel released or pushed forward, the connection to the GND will be open.
===Can I supply Spin-Y with 5V when connecting to VESC?===
Yes you can,  the firmware manages it within 0-3.3V range independent of supply voltage, and the center voltage is still 1.65V, unless the supply voltage is lower than 3.3V.
==Caution and limits==
Warning : 

# Throttle can not disengage Cruise when driver presses Brake Lever - scooter will slowdown with motors disengaged as long as you hold the lever, but once Brake lever released Scooter will get back to Cruise speed. (it is useful feature in city driving in lower power mod, but Be careful in high power modes).
# “End point Configuration” process will start your motors spinning, have your scooter on a riser (wheels in the air).

==Notes==
==See also==
[[Main page]]