Adapter V2 manual

This is the manual of HW V02, the newer hardware version is in progress, waiting our users to feedback.

The V2 adapter is designed to make convenient for users to connect wires of e-bike/e-scooters to the VESC. Combine with Ubox V2, We can easily to build an e-bike/e-scooter.

This manual is based on Ubox V2, for the other VESCs, the conceptions are the same.

Features

1. Horn, head light, turn light, brake & rear light, and reverse light support.
2. High, middle, low, 3 level throttle support.
3. Support both hall brake and mechanical brake input.
4. Two / one wheel drive support.
5. Power limit for compliance to the regulations.

Mode switching

Adapter V2 has 2 mode switching: 2/1 wheel drive mode switching and power limit mode on/off.

2/1 wheel drive mode

Hold both the right and left brake handles then power on the system, the adapter will toggle the 2/1 drive mode, after the switching, the buzzer will ring once for 1 wheel mode, and twice for 2 wheel mode.

The principle of 2 wheel drive is to copy the control signal from main ESC to the second ESC. In order to implement this function, the CAN bus connection of two ESCS need to set off, for Ubox, please refer: The power button of Ubox#The click button configuration.

Power limit mode

Hold both the left brake handle and the throttle handle bar, then power on the system, the adapter will toggle the power limited/unlimited mode, after the switching, the buzzer will ring three times for unlimited mode, and twice for limited mode.

The principle of Power limit mode is to scale the throttle handle bar's input to the L level, ignores the H, M, L state. So set the L level to meet your local regulations.

Setup in VESC tool

Before setup control logic to the VESC, we need to setup motor's FOC first. The following contents are based on VESC tool PC edition.

For 2/1 switch-able configuration, the setup is a little more complicated.

The Ubox has a internal 2.4G receiver, in this application, we can disable receiver, by click the button 9 times after the Ubox powered on and the button LED solid.

2 wheel drive mode only

If you want 2 wheel drive mode only, you can config the two ESC of Ubox into CAN mode, let the control signals relay through the CAN bus. We can let the wizard to finish the input setup.

1. After Ubox power on, and button LED solid, click the button 6 times, then wait 1 second, the internal CAN bus connection is on.
2. Plug in the ADC cable only from adapter's main socket to ESCA's socket.
3. Set you throttle handle bar's H-M-L switch to H position.
4. Then use a USB cable plug into ESCA, on the VESC tool PC edition:

In this step, pull the throttle and the brake handles, to let the ESC learn the input signal. If you don't have handle for brake, switch the brake mode switch to 'SW' mode, then use a screw to adjust the 'BRK' potentiometer to fulfill the ADC CH2 learning.

Go to APP Settings->General->APP to Use, set it to ADC.

Click Write app configuration, to save configuration to ESC.

Finished, to check if all the controls are working correctly.

2/1 wheel drive switch-able

If you want a switch-able system, you need to separate two ESCS from CAN bus, let them working alone. And set each of them one by one.

1. After Ubox power on, and button LED solid, click the button 7 times, then wait 1 second, the internal CAN bus connection is off.
2. Plug in an ADC cable from adapter's main socket to ESCA's socket.
3. Plug in another ADC cable from adapter's second socket to ESCB's socket.
4. Set you throttle handle bar's H-M-L switch to H position.
5. Then use a USB cable plug into ESCA, setup ESCA first.

On the VESC tool PC edition:

1.Click connect.

2.Read out APP configuration.

3.Goto APP Settings->General->APP to Use, set it to ADC.

Then

Go to APP Settings->General->ADC->General->Control Type set it to Current Reverse ADC2 Brake Button.

Then

1.Goto APP Settings->General->ADC->Mapping page.

2.Set mode to Current Reverse ADC2 Brake Button.

3.Click Reset min and max.

4.In this step, pull the throttle and the brake handles, to let the ESC learn the input signal. If you don't have handle for brake, switch the brake mode switch to 'SW' mode, then use a screw to adjust the 'BRK' potentiometer to fulfill the ADC CH2 learning.

5.Click Apply.

6.Click Write app configuration, to save configuration to ESC.

ESCA is finished, click disconnect, connect the USB cable to ESCB, do the above config for the ESCB.

When two ESCs are finished, to check if both ESCA and ESCB are working correctly.

See also

Main Page